PLUMBING ESSENTIALS: A PREREQUISITE FOR INSTALLING A BATHTUB

Plumbing Essentials: A Prerequisite for Installing a Bathtub

Plumbing Essentials: A Prerequisite for Installing a Bathtub

Blog Article

Website

What are your thoughts and feelings about A Step-by-Step Guide to Installing a Bathtub?


How to Install a Bathtub
Setting up a bathtub isn't exactly brain surgery, but it does call for strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably challenging job. If the old bathtub is readily obtainable, the task can relocate immediately; if you need to open up a wall to eliminate the old bathtub and also position the brand-new tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly require a helper to vacate the old tub and set in the brand-new one. See to it you have certified yourself for the task as well as fit trying it. Rather than hiring a service provider to take over a halfway-completed job, it is much better to take into consideration employing one prior to you begin. Possibilities are you may require an expert plumber to make tube links.
This short article will certainly assist you install a brand-new tub in your restroom if you have actually currently acquired a new bathtub as well as don't need to transform the plan of your previous supply of water pipes.
Your devices and also material checklist ought to make up the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Planning for the Installation


    Firstly, the sustaining framework supplied with the bath must be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to ensure that if the faucet features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps system to stop strain on the tub.
    Fit the adaptable faucet adapters to the bottom of both taps utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you use every one of the supplied washers.
    Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its last setting.

    Removing Old Touches


    If you need to replace old faucets with new ones as a part of your installation, then the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be quite troublesome because of the limited gain access to that is usually the case.
    Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will come from the pipelines. When the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old sealing substance.
    Before going on to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.

    Installing the Bath tub


    Utilizing both wood boards under its feet, place the bath tub in the called for placement. The wooden boards are practical in uniformly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four little points.
    The next goal is to make sure that the bath tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the tub till the level reviews degree.
    To set up faucets, fit the bottom of the furthest flexible tap connector to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
    Activate the water system and check all joints and also brand-new pipework for leaks and also tighten them if necessary. Fill the tub and also inspect the overflow outlet and also the normal electrical outlet for leakages.
    Finally, take care of the bath paneling as explained in the producer's instruction manual. Tiling and securing around the tub should wait up until the bathtub has been used a minimum of when as this will certainly settle it right into its final position.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a connection to the existent supply pipelines.
    If you require to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in location in between the faucet as well as the sink. Secure the faucet in position with the producer supplied backnut. As soon as the tap is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The former type must be connected to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.

    Tiling Around the Tub


    In the area where the bathroom fulfills the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, triggering the water to penetrate the wall surface in between the bathroom and also the tiling, leading to difficulties with moisture and also feasible leakages to the ceiling below.
    You can select from a selection of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and cartridges, and also can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to enable the activity experienced when the tub remains in use. The sealant can crack fairly very early if you do not consider this motion prior to sealing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the market. It is advisable to fit the ceramic tiles making use of waterproof or waterproof adhesive and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    I'm certainly very focused on How to Install a Bathtub Yourself and I'm hoping you enjoyed the page. Enjoyed our blog entry? Please share it. Let somebody else find it. We enjoy reading our article about Installing A Bathtub.


    Emergency? Depend on our professionals.

    Report this page